I always wondered, is it possible to make a disco ball with your own hands? I tried and it turned out that it is possible. In order to make a disco ball with our own hands, we need a balloon, newspaper, water, paste, CDs and glue. 1. We make the basis for the disco ball using the papier-mâché technique. On the balloon inflated to the required size, we stick the newspaper pieces soaked in water in one layer.
Read MoreIngredients: tomatoes - 5 kg, bell peppers - 0.5 kg, carrots - 0.5 kg, onions - 0.5 kg, sour apples - 0.5 kg, hot pepper - 2 pcs., Garlic - 200 gr. , salt - 1 cup without top, vegetable oil - 0.5 cups, sugar - 1 cup. Method of preparation: Wash the tomatoes and put them on a colander. Then cut them not 4 or 6 parts.
To make this nozzle, it is necessary to cut off two pipe blanks with a rectangular profile with a grinder. Two pieces of 20 cm long are enough. It is also necessary to cut two plates of 15 cm long. The billets must be processed and burrs removed. Sections of profile pipes are welded to the plate.
With this simple home-made device, you can wind steel wire of different thicknesses (that is, twist it into a spiral) on a shaft of a certain diameter. To make this tool you will need a minimum of time and materials: a piece of a rectangular steel plate; a piece of round pipe of suitable diameter; two sections of a profile pipe of square section; a piece of steel round bar for a handle.
In this article I will talk about how you can simply make an inverter for LDS. I needed it to check the backlight of the lamp matrices of laptops. In such matrices, an ordinary gas discharge lamp of a very small diameter is installed as a backlight. And like any similar lamp, it only starts if a lot of potential is applied to the threads.
This decoration with plastic suede will be a great addition to summer outfits. For work we take materials: - foamiran yellow, green and pink colors. - glue gun. - thin light green satin ribbon. - 6 beads. - lighter. - foil. - round mesh hair dummy. - a needle with a thread.
There are several simple but effective ways to assess the condition of the engine of any car without visiting service centers. This knowledge will be useful not only for the daily operation of the vehicle, but also help to make the right choice when buying a used car. What will be needed for diagnostics? The entire inspection is carried out visually and does not require a special tool.
To make such a holiday card you need: - cardboard. - scissors. - glue gun. - compass. - purple beads. - tweezers. - A ribbon for decorating floral bouquets in two different shades: orange and lilac. - transparent tape. - large silver beads. - stapler.
In a conventional bench vise, it is quite problematic to securely fix a round pipe (for example, to cut a thread). If you squeeze the jaws of the vice very hard, then the pipe may deform (especially thin-walled). If, on the contrary, you do not squeeze the vise, then it will rotate around its axis and it will simply be impossible to work with it.
To make the simplest solar concentrator (in common people - a lens) with your own hands, you will need ordinary ice, which can be easily "prepared" at home - in the kitchen. Moreover, the lens should turn out concave, and therefore it is better to use two convex glass covers from modern pans as a form.
Hacksaw in the economy is one of the most important tools. It’s often necessary to saw off, twist or shorten something, but a hacksaw is not always at hand. Today's homemade product is a kind of power tool designed for sawing small wooden parts. It is based on a wide sheet of metal from a hacksaw.
Matryoshka has long been a visiting card of Russia. "Russian beauties", as our guests from far abroad call them, delight the eye in any performance: painted from wood, clay and ceramics and, from colorful patches, made using the patchwork technique. Such a nested doll is very multifunctional. It can be put on the refrigerator or hung on the wall in the kitchen, set hot tea, while decorating the table.
From old or broken pliers, you can make a simple hand tool for crimping the ends of sheet metal pipes. This device is useful in cases where you need to slightly narrow the end of the pipe - to insert it into another pipe of the same diameter. The pliers will need to cut off the lips almost under the base.
From a conventional electric motor and improvised materials, you can assemble a practical and very convenient to use budget option of a home-made grinding machine for a home workshop or garage. At the same time, the obvious advantage of this homemade product is its lower cost compared to factory models.
If you are engaged in the manufacture of fences or beautiful window grilles, then various conductors will help you facilitate the work. And to make them quite simple. In this review, the author tells in detail and shows how you can do it yourself do-it-yourself simple home-made jig for making curls.
The obvious advantages of a home-made sharpening device are: compactness, ease of use, as well as simplicity of design and low cost of the materials used. The budget option for knife sharpeners is the best solution for home and garden. Since the main criterion for the manufacture of this home-made sharpening device is the affordable cost and simplicity of design, we will use wood as the main material.
Using decorative plaster travertine, which imitates natural stone, you can make the interior more original and unique. That's just worth decorative plaster is not cheap. However, you can make a budget option for wall decoration for travertine, using conventional putty. True, it is worth noting that the labor costs in this case will be more.
In the presence of old bars and sections of a profile pipe, you can make your own hands a simple bench for a summer residence. First of all, it will be necessary to remove self-tapping screws and nails from the bars, if they are there. Since the author uses old bars, which for a long time lay in the open air, they need to be processed with an electric planer (or on a planer).
Many people have old manual meat grinders lying around in the forge - it’s a pity to throw it away, but it makes no sense to use it. There are several options for its "modernization", you don’t have to throw it away, the old thing can still be useful. We offer one of them - to make a juicer out of it. What you need to have In addition to the meat grinder itself, you need to prepare a drill and a tap for threading M12, a sleeve with the same thread and an ordinary self-tapping screw to fix the meat grinder to the surface.
All girls love jewelry. How nice it is when for all occasions in the "treasury" is a suitable decoration. However, it so happens that it is not always found what to wear with the selected clothing. Skilful hands, fittings and some free time come to the rescue. Do not worry, it’s not at all difficult to make jewelry; now you’ll see for yourself. Read More
Copyright © 2024 Crazy hands
https://uaft2404.org au.uaft2404.org © 2024